Workline Dynamics XA50 - USA

myExam Autopilot Workline Dynamics Job Aid The Workline provides an overview of the steps which need to be done for specific exam programs and modes. It changes dynamically during the exam. Brain Autopilot | Standard | 20:04 Remaining Time SAR 0:32 O 2:58 4:28 2:12 2:58 O 6:56 AAHead_Scout Start Stimu N AAHead_Scout Checkoutcas t1_se_sag t2 tse dark- fluid_tra_p2 4scan_trace. t2_tse_tra Quality Inject contrast 11_mprage sag_iso Summary It can also include the steps for image checks and any needed interaction steps for the examination, e.g. contrast injection, spine planning. Planning Step Contrast Step The workline follows the workflow status and adapts automatically if changes are done. In fact, step icons change during the examination to provide an easy understanding of the current situation. Above the workline, you can always see the Head | Standard Scan | 3:30 remaining time current Programs, Mode, and the remaining scan time. If the program is modified (e.g., SAR NM mode or decisions are changed in the Exam Settings), the Workline and its information are Stimu NM adapted to show the new settings, the new workflow steps, and the scan duration. The needle on the icon indicates the current running step or the step ready to start. The white highlighted border indicates the current selected step. 0:30 O 0:30 1:00 Each steps shows the scan time before and during the scan. In addition, you can click on Localizer Quality Check T1 sag dark 12 tra each step and review the sequences for fluid image quality. Relative information and options for the selected step are displayed in the details area (see below). Restricted by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2022 SIEMENS Master Template Effective Date: 3 MAY 2020 | HOOD05162003074494 Job Aid Effective Date: Jul 9, 2022 | HOOD05162003288722 Healthineers Job Aid | myExam Autopilot Workline Dynamics – Numaris XA50 Effective Date: Jul 9, 2022 | HOOD05162003288722 Note: Steps cannot be re-ordered from the myExam Autopilot view. SIEMENS Healthineers Anatomic regions were Series AAHead_Scout detected successfully Depunt stop 1. WHead Back Brain Autopilot | Salud | 16.55 ExTuning hire SAR 1.58 Chau NM AAllasd Scout Chucklimace 12 toe dark- 12 hersa 8 1 9 8 0 EN 10:18:11 AM The Workline Control show the step currently running or the step that is getting ready to run. In addition, you can Start/Stop or Pause AAHead_Scout Start the workflow. If you click Pause while a measurement is still in progress, the measurement is completed and then the workflow pauses. If a 114 pause is activated, you cannot start a step. The workflow resumes after the pause is deactivated. Restricted by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2022 SIEMENS Master Template Effective Date: 3 MAY 2020 | HOOD05162003074494 Job Aid Effective Date: 03/03/2022 | HOOD05162003262278 Healthineers Page 2 of 4 Job Aid | myExam Autopilot Workline Dynamics – Numaris XA50 Effective Date: Jul 9, 2022 | HOOD05162003288722 Action Badges If an action is required to continue the workflow, an orange badge marks the step in which this interaction is required. The badge only appears when the step is not selected. The action badge may be used to mark any of the following: O • Exam Settings icon • Quality Check step • Contrast step • Planning step Overview of Icons’ Dynamics Preparing Pending Running Recon Done 4:58 0:57 3:45 Viewed Quality Check Contrast Step Planning Step Summary Step o Restricted by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2022 SIEMENS Master Template Effective Date: 3 MAY 2020 | HOOD05162003074494 Job Aid Effective Date: 03/03/2022 | HOOD05162003262278 Healthineers Page 3 of 4 Job Aid | myExam Autopilot Workline Dynamics – Numaris XA50 Effective Date: Jul 9, 2022 | HOOD05162003288722 Please note that the learning material is for training purposes only. For the proper use of the software or hardware, please always use the Operator Manual or Instructions for Use (hereinafter collectively “Operator Manual”) issued by Siemens Healthineers. This material is to be used as training material only and shall by no means substitute the Operator Manual. Any material used in this training will not be updated on a regular basis and does not necessarily reflect the latest version of the software and hardware available at the time of the training. The Operator Manual shall be used as your main reference, in particular for relevant safety information like warnings and cautions. Note: Some functions shown in this material are optional and might not be part of your system. Certain products, product related claims or functionalities (hereinafter collectively “Functionality”) may not (yet) be commercially available in your country. Due to regulatory requirements, the future availability of said Functionalities in any specific country is not guaranteed. Please contact your local Siemens Healthineers sales representative for the most current information. The reproduction, transmission or distribution of this training or its contents is not permitted without express written authority. Offenders will be liable for damages. All names and data of patients, parameters and configuration dependent designations are fictional and examples only. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. © Siemens Healthcare GmbH 2022 Siemens Healthineers Headquarters Siemens Healthcare GmbH Henkestr. 127 91052 Erlangen, Germany Phone: +49 9131 84-0 siemens-healthineers.com Restricted by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2022 SIEMENS Master Template Effective Date: 3 MAY 2020 | HOOD05162003074494 Job Aid Effective Date: 03/03/2022 | HOOD05162003262278 Healthineers Page 4 of 4