VA21D MULTIX Impact Family FD Calibration Video

This video will demonstrate how to perform FD calibration. To perform FD calibration, ensure you are logged in with the user account which has the FD calibration permission. Then access the service mode of the image station. Move the tube stand away from the tabletop and position the tube pointing towards the floor. Place the detector on the floor in the landscape position. Center the detector in the beam field and columnate the beam field to fully cover the active detector area. Please note, put the detector on a plastic foam sheet, otherwise the floor may be too cold and cool down the detector. Set the tube to maximum S ID, which should be at least 150 centimeters, but 180 centimeters is recommended. Use the retractable ruler to measure the set Sid. Be sure to make a note of the Sid as it will be needed for calibration. Insert the point 6mm copper filter on the user interface. Click FD Calibration. Please wait a moment while the system verifies the detector parameters and warms up. Enter the measured Sid in the current value box and click OK. A confirmation dialogue appears. Ensure that the 0.6mm CU filter has been inserted and click OK again. A confirmation dialogue appears. Turn on the calibration switch and click OK to continue. The calibration switch can be found on the backside of the generator on off console. Ensure that nobody is in the examination room and click Begin to start Automatic X-ray release. The calibration is then started. Warning Do not turn off the calibration switch When the calibration is in progress, wait until the calibration is finished. A total of 13 images will be taken and then another confirmation dialogue will appear. When the calibration is complete, click OK to save the calibration results. Wait until the calibration results have been saved successfully. A confirmation dialogue will appear as an indication that the results have been saved. Please note make sure to repeat the detector calibration by clicking Long Time Exposure before rebooting the system, otherwise the calibration will fail. Then click OK and reboot the entire system to activate the new files. You can also click on FD management to check if the new calibration due date has been updated. Lastly, it is very important to turn off the calibration switch for normal operation of the system or else radiation is not possible. If for some reason the calibration does not succeed, the previous calibration remains valid.

06:45:14 06:45:15 14:58:52 14:58:53 14:58:54 94% 14:58:55 14:59:05 150 14:59:06 93% 14:03:13 14:03:15 06:55:40 06:55:41 06:55:42 06:55:43 06:55:44 06:55:45 06:55:46 06:55:47 06:55:48 06:55:49 70 14:03:24 160 14:03:25 14:03:40 14:03:55 14:04:10 14:04:39 14:04:55 14:05:09 14:05:24 14:05:39 14:05:54 14:06:09 16 14:06:39 20 14:07:09 14:07:24 14:07:39 32 14:07:54 14:08:07 14:08:09 14:08:11 14:08:13 14:08:15 14:08:17 14:08:18 14:08:29 14:08:32 14:08:34 14:08:36 14:08:38 14:08:40 14:08:43 14:08:45 14:08:47 14:08:48 96% 13:51:06 14:20:51 14:20:57 14:20:58 14:20:59 14:21:00 14:21:01 14:21:02 14:21:03 80 14:22:05 14:22:55 14:23:45 14:24:35 14:25:25 14:26:15 14:26:42 14:26:52 14:27:01 14:27:02 14:27:03 14:27:08 20250614 14:27:11 14:27:12 14:27:13 14:27:14 14:27:15 07:02:00 Siemens Healthineers proudly presents Multix Impact & FD Calibration video valid for VA20D and upcoming software versions siemens Search Operation Result List Healthineers Log Off Pre-registered Patients Examined Patients Archiving Information Recyde Bin ID: Name Day Clear RIS Statu Nam Sex SPS Description Accession No. Display RIS update all result Total count: 0 Normal count: 0 Failed count: 0 Remove repeated entries: 0 Images 0% HU Name: AccNo SIEMENS SIEMENS . EMENS thineers althineers Tool OGP Editor Clean Archiv ... FD Calibration FD Reconnect RIS Mapping Statistics Test Image Tube Load User Setting Exam Site Info. General Processing Setting Image Display Register DICOM Disk Manager Ortho Setting Auto Thorax User Manager Service Remote PMS DICOM Node Assistance Access FD Manager Sensitivity Remote interface OR teamplay Fleet 10% HU D Reconnect FD Calibration Detector: PIXIUM3543EZh Serial number: 2031GU Check FD parameters for calibration Instructions: Please ensure that no additional objects are in the beam path (e.g. filter)! Please wait while the system verifies detector parameters Ready Current value Remarks SID NO Put the detector on the floor and turn it to landscape position. Center the detector in beam field and collimate the beam field to fully cover the active detector area. Please set the tube to maximum SID (at least 150 cm) and enter the measured value[cm]. Grid Please remove the grid! 29.5℃ Temperature range [10,41]℃, Please wait Omin Temperature constant Battery Capacity YES Battery capacity bigger than 50% Cancel Properties Audit Trail User Manager Ortho Setting FD Reconnect Calibration conditions OK PEPCO 7% HU Confirmation Is the following filter inserted: 0.6 mm Cu Click "Cancel' to abort the calibration. Tube is not aligned to detector. |3/4| Please change calibration switch to ON. Insert detector into table bucky. |4/4| PEPconnect Calibration switch: ON |1/5| e change Detector Calibration Dose 25000 nGy No Reference Image No Reference Image No Reference Image No Reference Image No Reference Image No Reference Image No Reference Image mAs ms Dose Density No Reference Image No Reference Image No Reference Image No Reference Image No Reference Image No Reference Image AEC Focus Cu filter 0.0mm Long time exposure Close Begir Abort Calibration switch: ON Mode kV No Reference Image No Reference Image No Reference Image Calibration switch: ON |2/21 Information No Reference Image No Reference Image No Reference Image No Reference Information age The calibration has finished successfully. Finished Saving calibration files ... No acq. IS not ready |1/21 Please dlose service switch, then restart system. Temperature range [10,41]℃, Please wait 9min Cance 8% HU STOP 25000 nGy No Reference Image No Reference Image No Reference Image Abor ige Detector Overview Serial number Calibration Due Shock Sensor Table Wallstand Free Detail Disconnect 2031GU LTE 20250614 PEPCOnnect Please note this learning material is for training purposes only. For the proper use of the software or hardware, please always use the Operator Manual or Instructions for Use (hereinafter collectively "Operator Manual") issued by Siemens Healthineers. This material is to be used as training material only and shall by no means substitute the Operator Manual. Any material used in this training will not be updated on a regular basis and does not necessarily reflect the latest version of the software and hardware available at the time of the training. The Operator Manual shall be used as your main reference, in particular for relevant safety information like warnings and cautions. Please note: Some functions shown in this material are optional and might not be part of your system. Certain products, product related claims or functionalities (hereinafter collectively "Functionality") may not (yet) be commercially available in your country. Due to regulatory requirements, the future availability of said Functionalities in any specific country is not guaranteed. Please contact your local Siemens Healthineers sales representative for the most current information. will be liable for damages. The reproduction, transmission or distribution of this training or its contents is not permitted without express written authority. Offenders All names and data of patients, parameters and configuration dependent designations are fictional and examples only. All rights, including rights created by patent grant or registration of utility model or design, are reserved. Unrestricted | Published by Siemens Healthineers AG | C Siemens Healthineers AG, 2024 Siemens Healthineers HQ I Siemens Healthineers AG Siemensstr. 3 91301 Forchheim Germany Phone: +49 9191 18-0 siemens-healthineers.com Healt