UniPOC™ Connect to a Remote Instrument and Send Remote Commands Simulation

Continue Continue Continue Continue Continue Continue Untitled Scene Select the RAPIDPoint® 500 device 12345. Note: In UniPOC™, you must right click on a device in the Location Tree to connect to a remote instrument. Blank unipoc_remoteaccess_1.mp3 In this exercise we will demonstrate how to connect to a remote instrument and send remote commands using UniPOC’s Remote Control screen. To begin this exercise we will start on UniPOC’s Dashboard screen. Right click on the instrument you want to connect to in the Location Tree. In this example let’s select the RAPIDPoint® 500, device 12345. Please select the RAPIDPoint 500 device 12345 to continue. Note: The Remote Control option is only visible for instruments that support remote control functionality. Select Remote Control. Blank unipoc_remoteaccess_2.mp3 Then, select Remote Control. Please select Remote Control to continue. Select Controls. Text Entry unipoc_remoteaccess_3.mp3 If prompted, enter the remote password. Once entered, the Remote Control screen opens with the connection status displayed in the blue banner. Select Controls to view the different display options. Please select Controls to continue. Toggle Fullscreen Toggle Scaling Toggle Fullscreen and Scaling Blank unipoc_remoteaccess_4.mp3 When you are remotely connected to an instrument you can view, monitor, and interact with an instrument to facilitate troubleshooting and data management. Here you have two different display options: Toggle Fullscreen and Toggle Scaling. When both are selected the remote instrument display covers the entire web page. You can also send Escape, Control Alt Delete, and Exit commands to the remote instrument. Note: In UniPOC, you must right click on a device in the Location Tree to send remote commands. Select the RAPIDPoint 500 device 12345. Blank unipoc_remoteaccess_5.mp3 Additionally, from the Location Tree, you can remotely interact with an instrument that supports remote commands and has been configured to do so. Again, select the RAPIDPoint 500, device 12345. Please select the RAPIDPoint 500 device 12345 to continue. Text Entry 1 unipoc_remoteaccess_6.mp3 Here we can send remote commands to instruments that support this functionality, such as the RAPIDPoint 500. Lock, locks the instrument, while unlock, unlocks the instrument. Suppression, lets you select the analytes you do not want to run on the instrument. Calibration, manually runs a 1-Point or 2-Point calibration. And Quality Control, runs an Automatic QC (AQC) measurement for Levels 1, 2, or 3. All commands sent to the instrument are logged and can be viewed in the Instrument Tracking Log or on the Edit Instrument screen. Congratulations! You have successfully connected to a remote instrument and sent remote commands. You can try the simulation again, or if you want to exit the learning activity, select Next to read the disclaimer and then close the training. Retry Next Completion Disclaimer Please note that the learning material is for training purposes only. For the proper use of the software or hardware, please always use the Operator Manual or Instructions for Use (hereinafter collectively “Operator Manual”) issued by Siemens Healthineers. This material is to be used as training material only and shall by no means substitute the Operator Manual. Any material used in this training will not be updated on a regular basis and does not necessarily reflect the latest version of the software and hardware available at the time of the training. The Operator Manual shall be used as your main reference, in particular for relevant safety information like warnings and cautions. Please note: Some functions shown in this material are optional and might not be part of your system. Certain products, product related claims or functionalities (hereinafter collectively “Functionality”) may not (yet) be commercially available in your country. Due to regulatory requirements, the future availability of said Functionalities in any specific country is not guaranteed. Please contact your local Siemens Healthineers sales representative for the most current information. The reproduction, transmission or distribution of this training or its contents is not permitted without express written authority. Offenders will be liable for damages. All names and data of patients, parameters and configuration dependent designations are fictional and examples only. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. UniPOC and all associated marks are trademarks of Siemens Healthcare Diagnostics Inc., or its affiliates. All other trademarks are the property of their respective owners. © Siemens Healthcare GmbH 2023 Siemens Healthineers Headquarters\Siemens Healthcare GmbH\Henkestr. 127\ 91052 Erlangen, Germany\Telephone: +49 9131 84-0\siemens-healthineers.com Disclaimer Exit To access your Certificate of Completion, select the Certificates tab from the learning activity overview page. You can also access the certificate from your PEPconnect transcript. You have completed the Connect to a Remote Instrument and Send Remote Commands Simulation. Completion HOOD05162003347702 | Effective Date: 27-Apr-2023 1.1 Blank 1.2 Blank 1.3 Text Entry 1.4 Blank 1.5 Blank 1.6 Text Entry 1 1.7 Completion 1.8 Disclaimer 1.9 Completion