Select&GO | General functions & features XA70A

In this video you will learn about the general functions and features of the Select and Go display from the XA70A upwards. You can operate the system and the patient table using the control units located on the magnet cover. The control unit consists of a Select and Go touch display and a jog wheel. With software version XA70A and higher, these new functions are available. Patient registration, ISO positioning. Starting the examination. You will learn more about these individual components during the training show and edit registered patient data. Automatic table positioning. Change the patient orientation table lock and unlock table position and target info, comfort and settings menus, guidance on the different body parts, connected coils, toolbar, exam, start button, laser function for manual positioning. You can gain access to the pre registered patient data from the Radiology Information system or the single acquisition workplace. You can edit the patient orientation or demographics as needed. Please note that other settings and patient information are read only and can only be changed in the single acquisition workplace or in the risks. Adjust the settings for patient comfort and control the settings for the Select and go displays. Here you can turn off all touch functions. This can be useful for example to clean the displays. You can change the settings for both displays simultaneously. Prepare the patient for various examinations with a step by step guide. Yeah, you can configure the ISO center manually by using the three sub pages, Body Regions, Biomatrix, Contour and Keypad. You can find more information about this three ISO positioning options in the training platform. Monitor physio signals and utilize the guide for electrode positioning. If a Biomatrix coil with beat sensor is connected, additional guidance for positioning is available. Moreover, you can view extra data on the physio card when it's linked with the Biomatrix coil. Select this function to fix the table position. Select the function above to change the patient orientation. Please note this is only available without my exam 3D camera. Select the laser function on the bottom of the display for manual positioning. For an automatic ISO positioning, select the required body region on the patient, press and hold the jog wheel for at least one second to move the table into the ISO center automatically. After successful ISO positioning, the start button is activated. Press it to begin the countdown and start the examination. You can find more Select and Go videos from XA70A upwards in the training platform.

150 06:44 5/28/2024 06:35 06:36 5/28/1979 45 11 176.37 176.3 2.1. 00:04 00:03 00:02 00:01 00:00 Select&GO General functions & features MAGNETOM Flow.Platform upwards XA70A SIEMENS MAGNETOM Flow Control units: The Select&GO touch display and a jogwheel. Patient registration Starting the examination Healthineers Register Patient Body Part - undefined Guidance C-Spine / Neck Coils BM Head/Neck Coil 0 deg BM Spine Coil T-Spine Deline Physio . Table Position Home Target ISO - Head Laser registered patient data Automatic table positioning Change the patient orientation Table lock/unlock Table Position and Target info Comfort and Settings menus Guidance on the different body parts Connected coils Tool bar Exam start button Laser function for manual positioning Pre-registered patient data from the RIS or the syngo Acquisition Workplace. 3 Procedure(s) Scheduled Today Patient Detalls Procedure Date & Time Doe, John 2024.05.28-06:37:00-DST-1.3 ... Mickey, Mouse Snoopy, XY Demographics Snoopy XY Gende M (Male) Examination Details Implant Scanning No Implant Any Polarization Patient Orientation Feet First Prone Medical Alerts Allergies Save Exami Edit M (M Head First Height Supine Prone Left Lateral Right Lateral Feet First Superman Wrist Supine Wrist Prone Elbow Prone Apply Medic RF Transmit Mode Feet First Supine Exam Define Control the settings for patient comfort. Comfort Settings Headphones Bore Light Speakers Cleaning Mode Brightness Right Display for the Select&GO displays. All Displays off Guidance in preparing the patient for various examinations. Hea Head Shoulder Hip Knee Set Isocenter Guidance: Head Manual: Body Regions BM Contour Keypad O WholeBody O Head O Shoulder O Heart / Thorax O Liver O T-Spine Current ISO Head Cancel BM Contour M Current ISO BM Contour M Coil Range 0 - 130 Physio signals and guidance for ECG/ Beat Sensor positioning. Beat Sensor Cardiac Resp PT ECG To ensure optimal electrode contact: If necessary, shave skin outside the examination room. Prepare skin with prepping gel, avoid solutions containing alcohol. Always use new electrodes. Never reposition used electrodes. To ensure optimal signal for Contour S Coil: (1) Position the sensor directly over the patient's heart. (2) Route the cable toward the foot end of the table. To ensure optimal signal quality for cardiac triggering, it is recommended to use a Contour M or Contour S Coil rather than a Contour L Coil. Resp Cushion Relearn Signals . Table Position Locked Fix the table position. orientation. Please note: Only available without myExam 3D Camera. isopositioning. Target ISO - Laser Position Brain Head/Neck Coill Automatic: Select the required body region for Press jogwheel > 1 seconds to automatically move the table into the isocenter. . Table Position 769 mm After successful isopositioning, the Start Start button is activated. . Table Position Isocenter Target Home Exam Starts in ... Select Start to activate the countdown and start the examination. Stop Head/Neck Coil Detailed information for Isopositioning or Register patient and start the exam. Please note that the learning material is for training purposes only. For the proper use of the software or hardware, please always use the Operator Manual or Instructions for Use (hereinafter collectively "Operator Manual") Issued by Siemens Healthineers. This material is to be used as training material only and shall by no means substitute the Operator Manual. Any material used in this training will net-be-updsred on a regular basis and does not necessarily reflect the latest version of the software and hardware available at the time of the training. The Operator Manual shall be used as your main reference, in particular for relevant safety information like warnings and cautions. mat Please contact your local Siemens Healthineers sales representative for the most current information. The reproduction, transmiss on or di will be liable for damages. All names and data of patients, parameters and configuration dependent designations are fictional and examples only. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Siemensstr. 3 91301 Forchheim Germany Phone: +49 9191 18-0 Please note: Some functions shown in this material are optional and might not be part of your system. Certain products, product related claims or functionalities (hereinafter collectively "Functionality") may not (yet) be commercially available in your country. Due to regulatory requirements, the future availability of said Functionalities in any specific country is not guaranteed. The reproduction, transmission or distribution of this training or its contents is not permitted without express written authority. Offenders Unrestricted | Published by Siemens Healthineers AG | Siemens Healthineers AG, 2024 Siemens Healthineers HQ | Siemens Healthineers AG siemens-healthineers.com