Performing a Stand Test VEXX

Performing a Stand Test (VEXX) Angiography – Application Software VExx* *Click the link below to review how to identify your system(s) software version. How to Find System Software Version The system requests a brake test regularly in a configurable time interval. (Default: 25 days) • The brake test must be performed in the Parking Position. • The brake test must be performed with no patient on the table and no additional loads. • If no brake test has been performed in the configured time interval, the message “Stand test necessary within # days” will appear • After the time has expired, the stand speed will be reduced. The message “Reduced stand/table speed – Perform stand test” will appear. 1. Tap C-Arm Position > System Positions or System Position from Direct Access Bar 2. Select Parking Position or Parking/Self Test 3. Press the stand/C-Arm joystick down and deflect it away from you, and hold it until the Parking Position is reached. a. The message “Stand Test: Deflect joystick to perform stand test # s” is displayed. b. # is the delay time: i. ARTIS pheno, it is configurable by Customer Service in the range of 1 to 60s ii. ARTIS icono floor, ARTIS icono biplane, and ARTIS ceiling, it is 15s 4. Press the stand/C-arm joystick down and deflect it away from you and hold it. a. The brake test is started and the message “Stand Test: running…” is displayed b. The system performs the brake test for each axle (6 times). 5. Once the test is completed, a message will be displayed: a. “Stand Test: Successfully completed” = Normal movements are possible again. b. “No system movement: Stand test failed, SC” = All movement of the stand are blocked; Table movements are still possible, in this case, call Siemens Healthineers Customer Service. Unrestricted 0 Published by Copyright © Siemens Healthineers AG 2025 SIEMENS Master Template Effective Date: 3/5/2020 | HOOD05162003074494 Job Aid Effective Date: 15 August 2025 | QR700026564 Healthineers Job Aid | Changing 3D Preset Effective Date: 15 August 2025 | QR700026564 Please note that the learning material is for training purposes only! For the proper use of the software or hardware, please always use the Operator Manual or Instructions for Use (hereinafter collectively “Operator Manual”) issued by Siemens Healthineers. This material is to be used as training material only and shall by no means substitute the Operator Manual. Any material used in this training will not be updated on a regular basis and does not necessarily reflect the latest version of the software and hardware available at the time of the training. The Operator's Manual shall be used as your main reference, in particular for relevant safety information like warnings and cautions. Note: Some functions shown in this material are optional and might not be part of your system. Certain products, product related claims or functionalities (hereinafter collectively “Functionality”) may not (yet) be commercially available in your country. Due to regulatory requirements, the future availability of said Functionalities in any specific country is not guaranteed. Please contact your local Siemens Healthineers sales representative for the most current information. The reproduction, transmission or distribution of this training or its contents is not permitted without express written authority. Offenders will be liable for damages. All names and data of patients, parameters and configuration dependent designations are fictional and examples only. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Copyright © Siemens Healthineers AG 2025 Siemens Healthineers Headquarters Siemens Healthcare GmbH Henkestr. 127 91052 Erlangen, Germany Phone: +49 9131 84-0 siemens-healthineers.com Unrestricted 0 Published by Copyright © Siemens Healthineers AG 2025 SIEMENS Master Template Effective Date: 3/5/2020 | HOOD05162003074494 Job Aid Effective Date: 15 August 2025 | QR700026564 Healthineers Page 2 of 2