MULTIX Impact Smart Virtual Ortho without Camera

MULTIX Impact Smart Ortho without camera MULTIX Impact VA20 and Higher Prerequisites: • An Ortho Long Leg or Full Spine organ program is selected • The collimator must be in the 0° lock-in-position • The tube unit is be positioned in detent and centered to the detector at the correct SID • For Ortho acquisitions at the wall stand, the detector unit must be in the 0° position • Position the patient upright on the Ortho Stand or flat on the tabletop. • The Ortho menu is displayed on the Tube TUI. Steps: 1. Double-click on the proper OGP to open the tool. Ortho OGP list FullSpine ap_w180_t130 S TODjant 250 2. Measure the Table-to-Object Distance (TOD) and enter it on the TUI (touchscreen). Basic More Ortho TOD (cm) 26.0 + - 8 0 Planned Ortho Images. 3. Ask the patient to close their eyes and turn on the collimation light. 4. Angle the X-ray tube, so the laser is aligned to the upper edge of the region of interest (ROI). Select the upper limit button on the tube touchscreen (TUI). Note: The start position is stored, and the icon is marked with a checkmark. SIEMENS Unrestricted I Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2023 Healthineers Master Template Effective Date: 3/5/2020 | HOOD05162003074494 Job Aid Effective Date: XX/XX/XXXX | HOOD/HILS Page 1 of 4 5. Angle the X-ray tube, so the laser is aligned to the lower edge of the region of interest (ROI). Select the lower limit button on the tube touchscreen (TUI): Note: The end position is stored, and the icon is marked with a checkmark. 6. Collimate the width of the region of interest (ROI), in this case, Ortho. Collimation in height will open to the full size of the detector, depending on its orientation. Performing Acquisitions and Postprocessing steps: 1. Ensure the correct exposure factors are set for each required step in the ortho series at the Control Console. 2. With the patient maintaining positioning, press and hold the acquisition switch until all exposures are completed, and the tube returns to its original position. Note: Releasing the acquisition switch before all images are acquired will result in the interruption of the series. The exam will need to be repeated in its entirety. 3. Once the series acquisition is complete, release the switch. Auto-composing of the image then occurs. Measurements can be made to the composed image before saving it under the View tab. Stitch Name: STITCH, , TEST Institution name: SmartSim chos Sex: M Acquisition time: 17-07.06 View Composing ID: Test11 Date of birth: 1998-02-02 Age: 025Y Request ID: Accession no.: Test 11 Measurement Label T. L R Ta AA MAS KV- Reference EXI: Current EXI DE DAP OGP name: Ortho_Finishe ww. 3232 Grid type: FOCUSED Abort SIEMENS Unrestricted I Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2023 Master Template Effective Date: 3/5/2020 | HOOD05162003074494 Healthineers Job Aid Effective Date: XX/XX/XXXX | HOOD/HILS Page 2 of 4 4. Adjustments to the composing process can be made in the Composing tab. Steps are adjusted from first to last by shifting the lower image left, right, up, or down relative to the image above. Select Next after each image. View Composing Composing controls Steps 5 Transition mode Blend Transparent 5. Select Save once completed to finish the process and save the composed image. Acquiring a second view: 1. Return to the examination tab and select Add OGP. Examination Postprocessing Stitch View Print Patient Information pGP List Patient Name: 2. Double-click the proper OGP for the Ortho exam and click the Add button. 3. Repeat the steps above. SIEMENS Unrestricted I Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2023 Master Template Effective Date: 3/5/2020 | HOOD05162003074494 Healthineers Job Aid Effective Date: XX/XX/XXXX | HOOD/HILS Page 3 of 4 Please note that the learning material is for training purposes only! For the proper use of the software or hardware, please always use the Operator Manual or Instructions for Use (hereinafter collectively “Operator Manual”) issued by Siemens Healthineers. This material is to be used as training material only and shall by no means substitute the Operator Manual. Any material used in this training will not be updated on a regular basis and does not necessarily reflect the latest version of the software and hardware available at the time of the training. The Operator's Manual shall be used as your main reference, in particular for relevant safety information like warnings and cautions. Note: Some functions shown in this material are optional and might not be part of your system. Certain products, product related claims or functionalities (hereinafter collectively “Functionality”) may not (yet) be commercially available in your country. Due to regulatory requirements, the future availability of said Functionalities in any specific country is not guaranteed. Please contact your local Siemens Healthineers sales representative for the most current information. The reproduction, transmission or distribution of this training or its contents is not permitted without express written authority. Offenders will be liable for damages. All names and data of patients, parameters and configuration dependent designations are fictional and examples only. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Copyright © Siemens Healthcare GmbH 2023 Siemens Healthineers Headquarters Local Contact Information Legal Manufacturer Siemens Healthcare GmbH Siemens Medical Solutions USA, Inc. Siemensstrasse 1 Healthcare Sector Henkestr. 127 40 Liberty Blvd. Forchheim, Germany 91301 91052 Erlangen, Germany Malvern, PA, USA 19355-9998 Phone: +49 9131 84-4746 Phone: +49 9131 84-0 Telephone: +1-888-826-9702 siemens-healthineers .com/radiography siemens-healthineers.com siemens-healthineers .com/en-us SIEMENS Unrestricted I Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2023 Master Template Effective Date: 3/5/2020 | HOOD05162003074494 Healthineers Job Aid Effective Date: XX/XX/XXXX | HOOD/HILS Page 4 of 4