Lateral Plane syngo DynaCT Job Aid

Lateral Plane syngo DynaCT Job Aid Lateral Plane syngo DynaCT allows the system to perform Dyna3D and DynaCT acquisitions with the Lateral plane (B plane). • Can fuse with Floor stand (A plane) imaging and then be used for intraprocedural plan- ning, guidance, 3D overlay, and clinical workflows. • 2D/3D Registration/Fusion must be performed on A plane to use 3D volumes acquired from B plane. • 3D Overlay Functions are not available on the B plane. 1. Move Lateral plane (B plane) to working area – on touch screen of Pilot Control Module select C-arm Positions  System Positions  choose any Biplane Position. • Lateral Plane syngo DynaCT can be performed with B Plane in Angio position or Card Position. ARTIS System Positions System Positions Switch Card / Angio Examination System Positions Patient Transfer C-Arm Position Anatom. Positions Head Side Detector RC Direct Positions Biplane Head Side Case Flows Current Positions Left Side Biplane Left Side Favorites 3D Positions V + Sys. Pos. Case Flows Display Exam Favorites Sys. Pos. Case Flows Display Exam Favorites Unrestricted | Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2023 SIEMENS Master Template Effective Date: 3/5/2020 | HOOD05162003074494 Job Aid Effective Date: XX/XX/2023 | HOOD/HILS Healthineers 2. Adjust Lateral plane (B plane) position longitudinally if needed. Acq. Protocol 5sDual DCT Body 4sDual DCT Body Care 4sDR [B] Body 4sDSA [B] Body 5sDCT [B] IQAP 4sDCT [B] Body Care Roadmap Overlay Settings C-Arm 3. Select dedicated 3D protocol for 3D acquisition with Lateral plane (B plane) – on touch screen of Pilot Control Module select Examination  Acquisition Protocol  Select a protocol with [B]. 4. Position the region of interest in the isocenter. To do so, follow the instructions in the message bar. • If B plane longitudinal position needs to be adjusted, deselect 3D protocol, move B plane to the desired position, and reselect the 3D protocol. • Only perform Fluoro using B plane fluoro. A plane fluoro will not be blocked. 5. Drive C-arm to the start position by pressing the joystick down and deflect it away from you. • Only perform Fluoro using B plane fluoro. A plane fluoro will not be blocked. 6. Perform 3D test run by pressing the joystick down and deflect it away from you. During the test run, make sure that no collisions will occur. 7. Perform a brief fluoroscopy on B plane fluoro pedal, for automatic setting of acquisition parameters. • A Plane fluoro will not be blocked. 8. Perform 3D acquisition from the handswitch or foot pedal. • Radiation of A plane will be blocked during 3D acquisition. Unrestricted | Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2023 SIEMENS Master Template Effective Date: 3/5/2020 | HOOD05162003074494 Job Aid Effective Date: XX/XX/2023 | HOOD/HILS Healthineers Page 2 of 3 Please note that the learning material is for training purposes only! For the proper use of the software or hardware, please always use the Operator Manual or Instructions for Use (hereinafter collectively “Operator Manual”) issued by Siemens Healthineers. This material is to be used as training material only and shall by no means substitute the Operator Manual. Any material used in this training will not be updated on a regular basis and does not necessarily reflect the latest version of the software and hardware available at the time of the training. The Operator's Manual shall be used as your main reference, in particular for relevant safety information like warnings and cautions. Note: Some functions shown in this material are optional and might not be part of your system. Certain products, product related claims or functionalities (hereinafter collectively “Functionality”) may not (yet) be commercially available in your country. Due to regulatory requirements, the future availability of said Functionalities in any specific country is not guaranteed. Please contact your local Siemens Healthineers sales representative for the most current information. The reproduction, transmission or distribution of this training or its contents is not permitted without express written authority. Offenders will be liable for damages. All names and data of patients, parameters and configuration dependent designations are fictional and examples only. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Copyright © Siemens Healthcare GmbH 2024 Siemens Healthineers Headquarters Local Contact Information Legal Maufacturer Siemens Healthcare GmbH Siemens Medical Solutions USA, Inc. Imaging & Therapy Systems Healthcare Sector Henkestr. 127 40 Liberty Blvd. Angiography & Interventional X-ray Systems 91052 Erlangen, Germany Malvern, PA, USA 19355-9998 Siemensstr. 1 Phone: +49 9131 84-0 Telephone: +1-888-826-9702 DE-91301 Forchheim siemens-healthineers.com siemens-healthineers.com/en-us Germany Telephone: +49 9191 18-0 siemens-healthineers.com/angio Unrestricted | Published by Siemens Healthcare GmbH © Siemens Healthcare GmbH, 2023 SIEMENS Master Template Effective Date: 3/5/2020 | HOOD05162003074494 Job Aid Effective Date: 01/09/2024 | QR700004005 Healthineers Page 3 of 3